Low Cost Surface Firmness Tester

If you're a broke datahead like me you probably have always wanted to measure your putting green surface firmness but haven't been able to justify the $1000+ expense to buy one of the fancy testers available on the market. The problem I have had is that I just wasn't sure if it would be a metric that would make a difference in the way I managed my golf course.

It was easy for me to justify the expense of a moisture meter almost 10 years ago because I could see how it would improve my operation. I'm still on the fence about the firmness tester so I asked twitter how I could make one for myself and as usual, was pleasantly surprised.

This rather simple firmness tester was brought to my attention but it was still out of my price range at around $500.

Dr. D made a great little video outlining these various devices and how they work.

I decided to make an even cheaper version than what the PGA currently uses, again, because I am not sure if this is something that is valuable to me.

I bought 2 steel balls that are close in size to a golf ball which is 1.68" in diameter. My steel balls are 1.5" but you could also use 1.75" balls. You can get these on Amazon.

My version uses your HOC gauge to measure the depth of the impression on your green. Don't tell your mechanic.

Instead of a washer I used an old bedknife that is the same thickness as the little knob below the HOC gauge.

center the hole with paint over the indent

Find a bedknife that is a similar thickness to the tab on the bottom of your gauge.

In order to get consistent data you need to drop the balls from a constant height. I use a flag stick (assuming all of your flags are the same height). I drop the balls from the bottom of the flag because no one else on my crew can reach the top!

This version requires you push down on the gauge to test the depth. This obviously introduces some error so be as careful as possible to not push too hard.

I take a few measurements then log them in my firmness tester spreadsheet found here.

I've been asked a lot about how much the balls should weigh. I don't think it matters much as long as all your balls are the same mass and size. The only reason to have a standardized ball would be to compare to other courses which isn't what this is for.

In time I expect to build an understanding of what this data means. What is firm and what is soft and if it's something that I care about enough to measure or invest further in one of the fancy units.

For now I've pulled this data into my maintenance HUD to see how important this data really is.

If you like my blog and want to support what I do you can support me on Patreon or paypal. Thanks!

If you like my blog and want to support what I do you can support me on Patreon or paypal. Thanks!

Turfgrass speedo is still my most important tool for managing turf growth after 4 years.

It wasn't the easiest year for growing grass , but the conditions were still pretty good. Almost 4 years ago exactly, I came up with the idea of comparing actual clipping yields to the "ideal" clipping yield or the clipping yield adjusted using the Growth Potential Model . Since then, it has proved to be a much more useful tool to manage growth than I originally thought . It has been almost a decade since I started making observations on plant health and playability and how it relates to the clipping yield. I have been constantly searching for ways to get the growth rate right as often as I can and this tool seems to be the best way I have seen so far, and might ultimately, be the best way going forward. To prove this point I will discuss in a future post, the success I've had with pest control in the past few years (for the most part (Not withstanding the times where I think my greens are dead but they actually aren't...thanks T)). Never needed less There are ...

Do you have enough?

I recently discussed how we can use fertilizer ratios to simplify how much fertilizer we apply to help us keep above the MLSN guidelines . When we get a soil test done it is a static amount of nutrients found in the soil. Even if you are above the MLSN guidelines at the time of testing, it doesn't guarantee that you will remain at or above the guidelines as the grass grows and consumes nutrients. There is math that you can use to determine exactly how much nutrient you need to apply to ensure that you remain at or above the MLSN guidelines. For many, this is much too complicated. For that reason I made a quick cheat sheet to help you determine how much of each nutrient you can expect to use each year based off a few different annual nitrogen rates. Nutrient use is based primarily on nitrogen use so the left 2 columns are a few different nitrogen rates. The columns for each nutrient are in PPM and are designed to help you look at your current soil test PPM (mehlich 3) and determin...

How to quantify nutrient content in liquid fertilizer

In a recent post, I discussed how it was actually cheaper to spray soluble vs granular fertilizer. What about if we use pre-mixed liquid fertilizer? How do we even figure out how much nutrient we are applying with pre-mixed liquid fertilizer? Before I learned that you could simply dissolve soluble fertilizer in water and apply it in a sprayer, I was a big user of pre-mixed liquid fertilizers. One of the issues I initially had was figuring out exactly how much of each nutrient I was applying. The math wasn't as straightforward is it was with granular fertilizers. It turns out, it's actually not that difficult but requires an extra step. First, we need to convert the liquid volume into a mass. Many products will have the product density displayed on the label or you can look in the Safety Data Sheet (SDS) for that information as well. No SDS? Should you be using products without an SDS? Even if this information isn't included on the label it is very easy to figure out. All ...

Fusariummy

Search This Blog